Presentation

X Ray Inspection system

X Ray Inspection system - certificate download (PDF 0,3 Mb)

X Ray Inspection system download (PPT 4,9 Mb)

BV-206

About All Terrain Vehicles  BV-206 загрузить (PDF 0,5 Mb)

Advantage All Terrain Vehicles BV-206 загрузить (PDF 0,7 Mb)

Characteristics of All Terrain Vehicles BV-206 загрузить (PDF 0,5 Mb)

http://youtu.be/qtm_uhKnfSg   

Video of field test on 29/06/2016 - https://youtu.be/epvbR1ahwSw

IZUMRUD -WCS Association till 2021 

WCS signs  5 years exclusive contract with Izumrud ( Russia) for water disinfectants ( Aquaeca technology ) & water purification (Saphire technology) for GCC, India, Pakistan & Egypt.

http://www.izumrud.com.ru/eng/about/ 

NEW OS (Single layer BIURS)

GENERAL PROPERTIES

System anti-corrosion coating BIURS SL is a two-component system that provides protection against corrosion of steel pipes with cathodic protection. Its high abrasion resistance combined with excellent adhesion and water resistance make it the best choice for protection of pipes.

Operating temperatures piping system with BIURS SL applied is up to 65 ° C (150 ° F) for underground laying and to 100 ° C (212 ° F) in air. BIURS SL coating can be applied in complex conditions requiring a short time for the repair and reopening of the pipeline.

PHYSICAL PROPERTIES

APPLICATION PROCESS

The main stages of the application

1. Remove oil, grease and loose deposits.

2. Clean the surface by sand blasting to  extent 2 (almost white metal) (according to NACE) or SA 2.5 (according to ISO 8501)

3. Apply BIURS SL desired thickness.

4. Leave to cure

5. Visually or electrically check for the presence of coating passes \ insufficient thickness.

6. Eliminate the disadvantages.

7. Surface Preparation

9. During the blast cleaning and till the end of coating application the temperature of steel surface should be 30C / 370F above the dew point.

10. Application Procedure

11. BIURS SL is applied to the cleaned surface of the steel using equipment with a plural componentfeeding. The ratio of the pump should be three parts A (base) to 1 part B (hardener).

12. Base BIURS SL (Part A), should be preheated to a temperature of at least 350C / 950F with constant stirring. It is recommended to use a transfer pump with liquid-to-air ratio not less than 10: 1, for supplying of the component to the pumps for the main equipment. Built-in heaters should be used to warm up the base (Part A) to 600C / 1400F temperature of the substrate.

13. BIURS SL Hardener (Part B) to be supplied with a transfer pump with liquid-to-air ratio not less than not less than 5: 1 and a minimum temperature of 150C / 600F. Stirring is not required unless a hardener not been heated to achieve the desired temperature.

14. The hoses off application equipment must be heated and heat-insulated to maintain the temperature of the material.

Hose for base (part A) has to have internal diameter of at least 3/8 inch (9.5 mm) and withstands the operating pressure of 5000 psi (345 bar).

Hose for hardener (Part B) has to have internal diameter of at least 1/4 inch (6.35 mm) and withstandsthe operating pressure of 6000 psi (414 bar). The maximum length of hose - 50 meters (55 yards)

15. The mixing unit must have shut-off valve installed in front of the unit and device for flushing by asolvent that will allow to wash off material residues.

16. The leash should have internal diameter of at least 3/16 inch (4.8 mm) and be not more than 5 m (5.5 yards) in length. Sprayer (pistol) must be a high-pressure airless sprayer with a minimum pressure rating of 3000 psi (207 bar). Nozzle size should be less than 0.027 inches (0.69 mm) and a maximum of 0.040 inches. (1.02 mm)

REPAIRS.

Repair of the coating must be performed by made one of 2 ways:

All statements, technical information and recommendations contained herein are based on tests that we believe to be reliable, but the accuracy or completeness thereof is not guaranteed, and the following is made in lieu of all warranties, express or implied: Seller and the manufacturer only obligation would be to replace a quantity of the product proved to be defective. Neither seller nor manufacturer shall not be liable for any injury, loss or damage, direct or indirect, arising from the use or inability to use the product. Before using, user shall determine the suitability of the product for its intended use and user assumes all risk and liability in connection therewith. These statements are not contained herein should not be any invalid if agreement signed by officers of the seller and manufacturer. 

 

Presentation by WCS (Exclusive distributor of technology in GCC, MENA region, India, Pakistan and Egypt)

Water treatment

Enterprise "," Technologies of XXI Century Center "Group of Companies was founded in 1998., which includes LLC" Technology Center of the XXI century ", LLC" PKF "Aquarius"

"7 TEH" and LLC "Siberian Research Institute."

The company works in close cooperation with the scientific support of the Department of Analytical Chemistry and Department of Chemical thermodynamics and kinetics of the St. Petersburg State University.

Ltd. "Technology Center of the XXI century" is a member of the Leningrad Region Chamber of Commerce and the Central-Siberian Chamber of Commerce.

The company specializes in the development of technologies, hardware design and manufacture of water treatment facilities and systems of industrial water treatment, desalination of sea water equipment.

The scope of the company includes the following areas:

- Desalination of sea water;

- Treatment of domestic wastewater biological treatment facilities of settlements;

- Water for houses and apartments, for EU standards for potable water, potable water from different sources in order to clean mechanical and colloidal inclusions, the dissolved impurities, including silicon, boron, bromine, dissolved iron and manganese organic compounds (humussubstances , organic chlorine compounds, etc.), reduced stiffness and salinity, water conditioning, water disinfection;

- Obtaining purified water for injection in medicine, dialysis pharmaceutical use;

- Waste water treatment stations car wash, drainage of industrial sites, gas stations, oil depots and other similar facilities;

- Sewage treatment enterprises of metallurgical and machine building, light industry, food, chemical industry;

- Cleaning of drainage water solid waste landfills;

- Treatment of liquid radioactive waste and gas emissions;

- Regeneration of spent pickling wastes based on sulfuric, hydrochloric, phosphoric, nitric acids, and mixtures thereof;

- Organization of the production of circulating water cycles;

- Industrial water treatment in the sectors:

• pharmaceutical

• medical

• food

• chemical

• galvanic

• Metallurgical

• mining

• energy

*electonics

- Introduction of membrane technology for separating liquids and concentration of components (proteins, pectin, lactose, enzymes, etc.), micro-, ultra-, nano filtration, reverse osmosis;

- Demineralization with ion-exchange resins mono sphere type of countercurrent regeneration technology;

- The construction, modernization and reconstruction of water treatment;

- The organization of complexes of accumulation and storage of purified water;

- Establishment of mobile system analysis, purification and water treatment for the armed forces and special units, geological survey expeditions, building towns, the bases of temporary residence;

- Warranty and maintenance services, repair of water treatment equipment and water treatment, supply of consumables.

The following algorithm is used for working with the customer:

1. Preparation of technical specifications, including chemical analysis of raw water, the requirements for purified (prepared) water and equipment performance.

2. The development of technical solutions.

3. The issuance of the offer to the Customer.

4. Conclusion of a contract for the supply, installation and commissioning of the equipment.

5. Development of the project.

6. Delivery of equipment.

7. Installation and commissioning.

8. Guarantee.

9. Contracts for service and supply of consumables.